Simple Guide to Fitting Any Skates 2017

width chart for sktesA Simple Guide to Fitting Skates

Finding the best fitting skates is a tricky proposition, especially for first-time buyers. Unlike shoes where you’ll just look at the shoe size, skates have a lot more things to consider before buying.

Today we are gonna look at a few of these. So pay attention or you’ll end up buying skates that hurt your feet. 

First, you’ll have to take note of the skate’s size but you’ll also have to pay close attention to the skate’s depth/arch, the width and your own weight.

Things to Consider When Fitting Skates
  1. Depth
  2. Arch
  3. Width
  4. Weight

Whatever you choose should satisfy each of the measurements listed above or you’ll end up hating your skates. Also note that skate brands may differ in their measurements, check out hockey skate reviews to find more about that.

Also careful of salespeople who try to convince you to buy the first pair of skate that you try on. As noted above, skate fitting is complex and will take time. Getting a great pair of  skates is essential if you plan on using your skates for longer than a few months. The next step is learning how to sharpen your skates.

Hockey Skate Fit Profile and Width

Take a quick look for your brand and see the different profiles with each brand. 

fit profiles for skates

4 Different Tests for Skate Fit 

  • Pen/Pencil Test
  • Toe and Stance Test
  • Stiffness Test
  • Finger Test

Although skate fitting itself is a bit complex in terms of measurements, there are some simple shortcuts to test the fit.

I’d suggest trying a few of these tests to get a better idea of which skates to get. 

1. Pen/Pencil Fitting Test ruler being used to measure size

Put on the skates (not necessarily both 😉 ) but leave the laces untied. Uncover the socks by pulling up the part of shoes underneath the laces (this is called the tongue).

Place a pen or pencil above and between perpendicular eyelets (the holes where the laces go through), this will serve to essentially balance it. The skate is considered a bad fit if the pen touches your foot (the instep). This means that the skates are too shallow for you. The skate is considered a good fit if the pen is well balanced and does not touch your foot.

Summary – Don’t let it touch your foot. 

2. Toe and Stance Test how to use a hockey stance

Familiarity of the athletic (hockey) stance is essential with this test. In athletic stance, your knees are bended forward and your body is leaning forward.

Lace up your skates and try to feel if your toes are touching the front part of the skates. Optimal fit means that your toes aren’t touching the front part whilst in athletic pose.

To check further, try standing up while still wearing stakes. Optimal fit means your toes are just brushing the front part of the shoes.

Deviation from the aforementioned conditions in this particular test may deem the skates being tested as unfit.

Summary – Don’t have your feet squished in.

3. Stiffness Test a man squeezing the back of a skate to make sure it fits

The general rule is that stiff skates are good ones. The stiffness supports the ankle thereby avoiding ankle and other related injuries. Testing the stiffness of a pair is pretty simple, just give your skate a squeeze (making this test virtually the easiest one of the batch discussed here). Avoid skates that give in rather easily when squeezed.

Very stiff skates are usually recommended for experienced skaters. Novices should avoid the stiff ones and try to purchase less stiff ones because they may not be able to break the skates. Failure to do so may impair there performance. However, novices should still avoid skates that have little to no stiffness because the shoes will not be able to support the ankles.

It is worth noting that different brands have different standards of stiffness (like sizes) built in to their boots. Some brands or types might be better suited for seasoned skaters while some are better suited for novices or first timers.

Summary – Your skates should be stiff and not too loose. Don’t worry they will mold to your feet. 

4. Finger-at-the-back Test another test to test the size of your skates

This is another test that will enable the buyer to determine the fit of the skates at hand. To be more specific, this kind of test will determine if the skates have the right ankle size.

While the first test (pen/pencil test) entails the laces being untied, this test will start with the tightening up of the laces. Wear it like you’re going to an actual hockey game. Lean forward so that there will be a bit of gap at the back of the shoes. Put a finger or two inside the gap and try to reach the heel inside. Placing two fingers all the way inside means the skate is a bit loose and is an ill-fit. Using a pair of loose skates may cause injuries, highlighting the importance of this test.

You don’t have to do all the tests listed here but doing more than one (plus the tips given by the local skates’ seller) will help.

Summary – You shouldn’t be able to put two fingers in. 

Breaking In

You’ll also need to wear the pair of skates to mold it to your foot. Blisters and other discomforts are normal for the first few weeks but after a month you’ll have a molded custom fit pair of skates. After a while you won’t want to depart with your skates.

Baking is usually a shortcut to this but almost all skaters with a new pair will undergo this “break-in” period. The break in period is actually like baking, where the mold of your foot is being impressed on the skates for better fitting (baking being the faster method). 

Baking and Skates?

The two words above may not make sense but ask any avid hockey player and they will tell you that baking skates is recommended.

Please take note that this is only true for the high-end products. Don’t go baking your Walmart skates. 

Baking in this sense is done so that your skates will be molded to fit your foot/feet. You will be asked to wear the pair after heating it inside the “oven”.

You can try to bake your skates at home but it would be better to bake it in the shops. Skates ovens are specialized and not the usual oven that you see around. Doing it on your own increases the risk of destroying your pair of skates. You don’t want to burn your pair to crisp.

Summary – Bake your skate at a skate shop for a quicker mold. Don’t use your mom’s oven. 

Online or Offline

There are so many choices, brands and methods to obtain skates. This can be a bit intimidating especially for first time buyers or novices. Luckily most quality skates come ready to mold to any foot shape and width.

Good luck!

 

Summary
Simple Guide to Fitting Your Skates
Article Name
Simple Guide to Fitting Your Skates
Description
Every wonder how to fit your skate and make them exactly the right size to avoid injury while protecting your feet. Check out our guide.
Author
Publisher Name
Skates HQ

We will be happy to hear your thoughts

Leave a reply